Installation
INSTALLATION
CAUTION / NOTICE / HINT
NOTICE:
- Do not remove/install the spiral cable with sensor sub-assembly with the
auxiliary battery connected and the engine switch (for Gasoline Model)
or power switch (for HV Model) on (IG).
- Do not rotate the spiral cable with sensor sub-assembly without the
steering wheel assembly installed, with the auxiliary battery connected
and the engine switch (for Gasoline Model) or power switch (for HV
Model) on (IG).
- Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
PROCEDURE
1. INSTALL NO. 1 SWITCH WIRE (w/ Shift Paddle Switch)
for Gasoline Model: Click here 
for HV Model: Click here
2. INSTALL SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) (w/ Shift Paddle Switch)
for Gasoline Model: Click here
for HV Model: Click here
3. INSTALL STEERING PAD SWITCH ASSEMBLY
Click here
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Click here
6. INSTALL STEERING WHEEL ASSEMBLY
| (a) Align the matchmarks on the steering wheel assembly and steering main shaft to install the steering wheel assembly. |
|
(b) Using a 10 mm hexagon socket wrench, install the steering wheel assembly set bolt.
Torque:
62 N·m {632 kgf·cm, 46 ft·lbf}
(c) Connect each connector to the spiral cable with sensor sub-assembly and steering wheel assembly.
7. CHECK STEERING WHEEL CENTER POINT
8. INSTALL HORN BUTTON ASSEMBLY
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization or
registration) that must be performed after parts are removed and
installed, or replaced during steering wheel assembly
removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
NOTICE:
- Do not remove/install the spiral cable with sensor sub-assembly with the
auxiliary battery connected and the engine switch (for Gasoline Model)
or power switch (for HV Model) on (IG).
- Do not rotate the spiral cable with sensor sub-assembly without the
steering wheel assembly installed, with the auxiliary battery connected
and the engine switch (for Gasoline Model) or power switch (for HV
Model) on (IG).
- Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
PROCEDURE
1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
2. REMOVE HORN BUTTON ASSEMBLY
Click here
3. REMOVE STEERING WHEEL ASSEMBLY
(a) Disconnect each connector from the spiral cable with sensor sub-assembly and steering wheel assembly.
| (b) Using a 10 mm hexagon socket wrench, remove the steering wheel assembly set bolt. |
|
| (c) Put matchmarks on the steering wheel assembly and steering main shaft. |
|
(d) Temporarily install the steering wheel assembly set bolt.
NOTICE:
Do not overtighten the steering wheel assembly set bolt.
| (e) Using SST, separate the steering wheel assembly. SST: 09950-50013
09951-05010 09952-05010 09953-05020 09954-05031
09957-04010 SST: 09950-60010 09951-00330 NOTICE:
Apply a small amount of grease to the threads and tip of SST (09953-05020) before use. |
|
(f) Remove the steering wheel assembly set bolt and steering wheel assembly.
4. REMOVE STEERING PAD SWITCH ASSEMBLY
Click here
5. REMOVE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) (w/ Shift Paddle Switch)
for Gasoline Model: Click here
for HV Model: Click here
6. REMOVE NO. 1 SWITCH WIRE (w/ Shift Paddle Switch)
for Gasoline Model: Click here
for HV Model: Click here
